AC Installation and Replacement in Arlington, TX
- HONEST
- RELIABLE
- PROFESSIONAL
Contact Us
Arlington is the largest city in the United States without a commercial airport, and it reflects that scale in its residential fabric — a sprawling 100-square-mile footprint where postwar neighborhoods from the 1950s and 60s in the city’s original core give way to the mass-production subdivisions of the 1970s and 80s, which in turn give way to the larger planned communities built out through the 1990s and 2000s in the far north and south. No two parts of Arlington are quite the same, and the HVAC systems inside its homes reflect that full span of construction eras and building types. What they share is a Tarrant County summer that tests every one of them equally.
Across Arlington’s varied neighborhoods, these are the signs that a system has reached the end of productive service life:
- The system runs continuously through peak afternoon hours without reaching the thermostat setpoint — a problem that shows up earlier and more severely in Arlington’s older neighborhoods where insulation levels and window efficiency lag behind newer construction standards.
- You have had refrigerant added more than once in two seasons, which indicates a recurring leak at a chronic stress point rather than a one-time service event — a condition that does not resolve on its own.
- Your home feels noticeably more humid than the thermostat reading suggests, especially in the mornings after the system has run overnight, pointing to a loss of dehumidification capacity that compounds discomfort through the entire summer.
- The system is 12 or more years old and has required at least one significant component replacement — compressor, coil, or control board — pointing to a system entering the phase where remaining components follow the same trajectory.
- Comfort has deteriorated gradually over several summers in a way that is easy to normalize until a comparison makes the decline obvious — rooms that used to cool quickly now take much longer, and the house never quite feels settled on the hottest afternoons.
- Your energy bills have climbed year over year without any corresponding change in thermostat settings or household occupancy, reflecting efficiency loss in aging equipment working harder for less output.
A free in-home estimate puts the actual condition of your system in front of you so the decision is based on facts rather than hope or assumption.
our services
What Drives AC Wear Across Arlington's Diverse Neighborhoods
Arlington’s sheer geographic scale — stretching from the Tarrant County line near Grand Prairie in the east to Mansfield in the south and the mid-cities corridor in the north — means the city contains more housing variety than most DFW communities three times its age. That variety produces different HVAC stressors in different parts of the city, and understanding which ones apply to your neighborhood is part of what a thorough installation evaluation addresses.
These are the primary local conditions driving AC wear across Arlington’s neighborhoods:
- Arlington sits at the geographic midpoint between Dallas and Fort Worth on the broad Trinity River prairie, where the flat, open terrain provides no natural wind buffering and allows summer heat to radiate freely from streets, rooftops, and parking areas — an effect amplified significantly in the Entertainment District and stadium corridor around AT&T Stadium and Globe Life Field, where millions of square feet of paved surface and commercial rooftop create a concentrated heat island that affects the residential neighborhoods immediately surrounding it.
- The city’s enormous stock of 1970s and early 1980s tract homes — particularly concentrated in the neighborhoods between Division Street and Arkansas Lane east and west of Collins Street — were built with minimal attic insulation, single-pane aluminum windows, and duct systems designed for equipment that no longer exists, creating a set of structural inefficiencies that no modern replacement system can fully overcome without accompanying envelope and duct improvements.
- Arlington’s expansive clay soils shift significantly with the city’s pronounced wet and dry seasonal cycles, and in the older neighborhoods near Johnson Creek and Village Creek — both of which carry significant drainage from the city’s western and central areas — periodic flooding and soil saturation events introduce moisture beneath slab foundations that stress refrigerant lines and disconnect hardware over time.
- The University of Texas at Arlington campus and the surrounding student-housing neighborhoods generate unusual occupancy patterns with high summer cooling demand from units that may be occupied continuously by rotating tenants, compressing equipment wear cycles faster than standard residential usage would produce.
- Arlington’s position in the I-20 and SH-360 storm corridor places it in the path of severe weather systems that track northeast across Tarrant County with particular frequency, producing hail events that damage condenser coils and power surges that damage control boards and capacitors in residential units across large portions of the city simultaneously.
Whether your home is in an older Collins Street neighborhood, a 1990s subdivision in far north Arlington, or a newer development near Mansfield, the specific conditions your system faces differ — and the installation that serves it correctly accounts for those differences rather than applying a one-size approach.
Our AC Installation and Replacement Services in Arlington, TX
Ellis Air Conditioning and Heating has served communities throughout Tarrant County and the broader DFW Metroplex for over 50 years. Arlington’s scale and housing diversity mean our technicians work across a wider range of building types, construction eras, and neighborhood conditions in this city than in almost any other community we serve. That breadth of experience is what allows us to evaluate each home on its own terms rather than applying a template.
Our Arlington AC installation and replacement services include the following:
- A complete in-home evaluation covering existing equipment condition, ductwork layout and integrity, attic insulation levels, window type and exposure, slab or foundation condition as it relates to refrigerant line routing, and any neighborhood-specific conditions such as Entertainment District heat island proximity or creek corridor moisture exposure.
- A Manual J load calculation tailored to your home’s specific construction era, insulation levels, window efficiency, and orientation — the only reliable way to arrive at the correct system size across Arlington’s wide range of building types and conditions.
- Full removal and EPA-compliant disposal of the existing system, including proper refrigerant recovery and recycling.
- Installation by NATE-certified, factory-trained technicians in fully stocked service vehicles, with most replacements completed in a single visit.
- Ductwork inspection and repair or sealing as needed, with particular attention to the original duct configurations in Arlington’s 1970s and early 1980s tract homes where system efficiency losses through duct leakage are among the most significant in the entire DFW market.
- Full system commissioning with startup testing, refrigerant charge verification, airflow measurement at all registers, and a complete homeowner walkthrough before the job is considered finished.
Every estimate is free, every proposal is written and itemized, and no work begins until you have reviewed and approved the full scope and cost.
Inside a Typical Service Visit: An Arlington Tract Home Replacement
Last summer, we were called out to see Carol, who owned a 1,700-square-foot home in a neighborhood just north of Division Street in central Arlington. The home was built in 1974 and had the characteristic footprint of Arlington’s mid-70s tract construction — single story, low-pitched roof, aluminum single-pane windows on the south and west sides, and an attic that functioned more like a solar oven than a buffer zone. The system — a replacement installed in 2010 — had been repaired the previous fall and was now failing to keep the west-facing living room and master bedroom below 80 degrees on afternoons above 95.
Our technician’s evaluation revealed a situation that reads as a checklist of 1970s Arlington construction problems. The 2010 system had been sized using a standard square footage calculation that did not account for the home’s single-pane west-facing window area — three large aluminum-frame windows that admitted intense late-afternoon solar load directly into the two most uncomfortable rooms. The original 1974 duct system, galvanized sheet metal throughout, had developed rust-through sections in two supply branches and was leaking a significant percentage of conditioned air into the attic before it ever reached the living space. The attic insulation measured R-11 — original to the 1974 construction and never upgraded — and was contributing to attic temperatures that our technician measured at 158 degrees on that particular afternoon.
We replaced the system with a correctly sized unit that accounted for the west-facing solar load, relined and sealed the two rusted supply branches, sealed all remaining galvanized duct joints throughout the system, and provided Carol with a written assessment of the attic insulation situation as a follow-up investment recommendation. Her living room and master bedroom reached target temperature consistently for the rest of that summer. She told us every contractor before us had blamed the windows and told her there was nothing to be done without replacing them — and was surprised to learn that a correctly sized system with a sealed duct infrastructure made a difference she could actually feel.
Why Arlington Homeowners Choose Ellis Air Conditioning and Heating
Arlington is a city where the range of homes is as wide as the city itself — from compact 1950s bungalows in the original core to sprawling two-story colonials in the northern subdivisions, with everything in between. Serving that range correctly requires a contractor with the depth and breadth of experience to evaluate each home on its actual merits rather than applying the same approach regardless of what the home actually is. Ellis Air Conditioning and Heating has been building that depth since 1975.
- More than 50 years of continuous service in the Dallas–Fort Worth area gives our technicians direct, hands-on familiarity with the full span of Arlington’s housing stock — from its oldest postwar neighborhoods to its newest planned communities in the far north and south.
- Our technicians average over 10 years of tenure with Ellis, meaning the person evaluating your home brings seasoned field judgment to a city where what is true for a 1972 tract home on the east side is completely different from what is true for a 2002 subdivision home near Mansfield.
- As a Carrier Factory Authorized Dealer, Ellis meets rigorous manufacturer standards for training and installation quality that protect your equipment performance and preserve full warranty coverage from the first day of operation.
- We hold a BBB A+ Rating, NATE certification, and TDLR licensing under Texas License TACLB002064, independently verified credentials that reflect our professional standard on every job regardless of neighborhood, home size, or construction era.
- Our large fleet of fully equipped service vehicles supports fast response across Arlington’s 100-square-mile footprint, with most installations completed without return trips for parts.
- We offer 24/7 emergency service, free in-home estimates, and written proposals with fully transparent pricing before any work begins.
Arlington is a big city with a lot of contractors competing for the work. What sets Ellis apart is 50 years of getting it right across every part of it.
AC Installation and Replacement in Arlington, TX
Ellis Air Conditioning and Heating serves homeowners throughout Arlington, TX with AC installation and replacement services backed by more than 50 years of experience in the Dallas–Fort Worth area. Arlington is the largest city in our service area by land mass, and its 100-square-mile footprint contains more residential variety than most DFW communities twice its size — postwar cottages, 1970s tract homes with original galvanized ductwork, 1990s two-story colonials with aging flex duct systems, and newer construction in planned communities near the city’s southern and northern edges. Each of those eras comes with its own set of installation requirements, and the approach that works in one neighborhood may be entirely wrong for a home three miles away.
What Arlington homeowners across all of those neighborhoods share is the same intense Tarrant County summer — and the same need for a system that is correctly sized, properly installed, and supported by a duct infrastructure that can actually deliver what the equipment produces. That is what we evaluate on every job, regardless of which part of Arlington it is in, and it is the standard we have held ourselves to in this community since before most of the city’s current housing stock was built.
Call today for a free in-home estimate. We will assess your home, your system, and your specific neighborhood conditions — and give you a written proposal with honest recommendations and transparent pricing.